{"id":9923,"date":"2024-06-18T14:00:37","date_gmt":"2024-06-18T12:00:37","guid":{"rendered":"https:\/\/docs.kentix.com\/knowledge-base\/wall-reader-bus-doorlock-wa7-v2-manual\/"},"modified":"2025-11-14T09:51:24","modified_gmt":"2025-11-14T08:51:24","slug":"wall-reader-bus-doorlock-wa7-v2-manual","status":"publish","type":"ht_kb","link":"https:\/\/docs.kentix.com\/en\/knowledge-base\/wall-reader-bus-doorlock-wa7-v2-manual\/","title":{"rendered":"Wall reader (bus) DoorLock-WA7-V2 – MANUAL"},"content":{"rendered":"\n
Datasheet KXC-WA7-IPx-V2<\/a><\/pre>\n\n
Overview<\/h2>\n\n
Kentix IP wall readers enable contactless control of doors with a MIFARE\u00ae DESFire\u00ae RFID chip. The wall reader is suitable for installation in intercom systems or behind front panels. The reader’s electronics are housed in a 23 mm high casing. The setup always consists of the actual wall reader and the connected Kentix AccessManager<\/a>. The wall reader is connected to the AccessManager via a 4-wire connection. The AccessManager itself connects directly to a Power over Ethernet (PoE) capable network switch. To control electric strikes\/motor locks, the SmartRelay offers two relay outputs and, depending on the power class of the strikes, an integrated PoE splitter with 24VDC output.<\/p>\n\n
For the operation of the wall readers (version: V2), a Kentix AccessManager for cable readers (KXP-2-RS) with a KentixONE software version of 8.2.0 or higher is required. Information about the relay and circuit diagrams including examples<\/strong> can be found here: AccessManager (Bus)<\/a><\/p>\n\n
Safety instructions<\/h2>\n\n
Installation<\/span><\/div>
Installation and commissioning may only be carried out by trained specialist personnel in accordance with the instructions.
No modifications of any kind, other than those described in an appropriate manual, are permitted to Kentix GmbH products.
Certain levels of protection must be provided when installing Kentix equipment.
Observe the relevant regulations for installations in the respective environment.
Only operate the products within the defined temperature range.
The instructions should be passed on to the user by the person carrying out the installation.
Kentix accepts no liability for damage to the equipment or components resulting from incorrect installation. No liability is accepted for incorrectly programmed units.
Kentix shall not be liable in the event of malfunctions, damage to property or other damage.
<\/div><\/div><\/div>
Use of the products, transport and storage<\/span><\/div>
Protect the device during transport, storage and operation from
Protect moisture, dirt and damage.<\/div><\/div><\/div>
Battery powered products<\/span><\/div>
Do not use products in potentially explosive atmospheres.
Only operate the products within the defined temperature range.
Installation and battery replacement may only be carried out by trained personnel in accordance with the instructions.
Do not charge, short circuit, open or heat batteries.
When inserting the batteries, pay attention to the correct polarity.
The devices must always be operated with the batteries intended for the product.
When changing batteries, always replace all batteries.
Dispose of old or used batteries properly.
Keep batteries out of the reach of children.  
<\/div><\/div><\/div>
Maintenance
<\/span><\/div>
Kentix devices must be checked for functionality as part of annual maintenance.<\/div><\/div><\/div>
Disposal<\/span><\/div>
Electrical appliances and batteries must be disposed of separately from household waste.
<\/div><\/div><\/div><\/div>\n\n
Controls<\/h2>\n\n
\"\"<\/figure>\n\n
  1. Connection terminal<\/li>
  2. DIP switch<\/li><\/ol>