{"id":4240,"date":"2023-02-27T17:16:45","date_gmt":"2023-02-27T16:16:45","guid":{"rendered":"https:\/\/docs2.kentix.com\/knowledge-base\/fingerprint-reader-doorlock-wa5-ip-operating-instructions\/"},"modified":"2024-07-30T11:33:24","modified_gmt":"2024-07-30T09:33:24","slug":"fingerprint-reader-doorlock-wa5-ip-operating-instructions","status":"publish","type":"ht_kb","link":"https:\/\/docs.kentix.com\/en\/knowledge-base\/fingerprint-reader-doorlock-wa5-ip-operating-instructions\/","title":{"rendered":"Fingerprint reader DoorLock-WA5-IP – MANUAL"},"content":{"rendered":"\n
DATASHEET KXC-WA5-IP2<\/a><\/pre>\n\n
The fingerprint reader enables unlocking doors using a fingerprint and RFID card\/token. This is a two-factor authentication (2FA), where both components are always required to open a door. Not only one finger or only the RFID card can be used. It is connected using a SmartRelay<\/a> and can then be connected to an AccessManager (KXP16) using Manager\/Satellite mode. The wall reader is surface mounted.<\/p>\n\n
Safety instructions<\/h2>\n\n
Installation<\/span><\/div>
Installation and commissioning may only be carried out by trained specialist personnel in accordance with the instructions.
No modifications of any kind, other than those described in an appropriate manual, are permitted to Kentix GmbH products.
Certain levels of protection must be provided when installing Kentix equipment.
Observe the relevant regulations for installations in the respective environment.
Only operate the products within the defined temperature range.
The instructions should be passed on to the user by the person carrying out the installation.
Kentix accepts no liability for damage to the equipment or components resulting from incorrect installation. No liability is accepted for incorrectly programmed units.
Kentix shall not be liable in the event of malfunctions, damage to property or other damage.
<\/div><\/div><\/div>
Use of the products, transport and storage<\/span><\/div>
Protect the device during transport, storage and operation from
Protect moisture, dirt and damage.<\/div><\/div><\/div>
Battery powered products<\/span><\/div>
Do not use products in potentially explosive atmospheres.
Only operate the products within the defined temperature range.
Installation and battery replacement may only be carried out by trained personnel in accordance with the instructions.
Do not charge, short circuit, open or heat batteries.
When inserting the batteries, pay attention to the correct polarity.
The devices must always be operated with the batteries intended for the product.
When changing batteries, always replace all batteries.
Dispose of old or used batteries properly.
Keep batteries out of the reach of children.  
<\/div><\/div><\/div>
Maintenance
<\/span><\/div>
Kentix devices must be checked for functionality as part of annual maintenance.<\/div><\/div><\/div>
Disposal<\/span><\/div>
Electrical appliances and batteries must be disposed of separately from household waste.
<\/div><\/div><\/div><\/div>\n\n
A Kentix AccessManager for cable readers (KXP-2-RS) is required to operate wall readers. Information about the relay and circuit diagrams including examples<\/strong> can be found here: Kentix SmartRelay (KXP-2-RS)<\/a><\/p>\n\n
Controls<\/h2>\n\n
DoorLock-WA5-IP front side<\/h3>\n\n
\"\"
DoorLock-WA5-IP Front view<\/figcaption><\/figure>\n
  1. Fingerprint sensor for creating the templates in the learning process and opening the door using the RFID card and fingerprint<\/li>
  2. Status LED for signaling the various modes and states of the reader<\/li>
  3. Integrated RFID reader, the entire surface serves as a reading surface<\/li><\/ol>