{"id":4096,"date":"2023-02-15T13:52:28","date_gmt":"2023-02-15T12:52:28","guid":{"rendered":"https:\/\/docs2.kentix.com\/knowledge-base\/keypad-touch-operating-guide-archive\/"},"modified":"2026-08-12T10:00:35","modified_gmt":"2026-08-12T08:00:35","slug":"keypad-touch-operating-guide-archive","status":"publish","type":"ht_kb","link":"https:\/\/docs.kentix.com\/en\/knowledge-base\/keypad-touch-operating-guide-archive\/","title":{"rendered":"KeyPad-Touch – USER MANUAL (ARCHIVE)"},"content":{"rendered":"\n

This device is not compatible with KentixONE<\/p>\n\n

The KeyPad is used to arm and disarm the AlarmManager on-site. Like the MultiSensors, the KeyPad is integrated into the AlarmManager\u2019s ZigBee\u00a9 wireless network. Please note, however, that the KeyPad does not function as a router and cannot affect the network\u2019s range. <\/p>\n\n

The KeyPad turns on when any key is pressed. The maximum operating time is then approx. 10 seconds. Within this time, an assigned alarm zone can be armed or disarmed. <\/p>\n\n

Safety instructions<\/h2>\n\n
Installation<\/span><\/div>
Installation and commissioning may only be carried out by trained specialist personnel in accordance with the instructions.
No modifications of any kind may be made to Kentix GmbH products, with the exception of those described in the relevant instructions.
When installing Kentix devices, certain degrees of protection must be guaranteed.
Observe the relevant regulations for installations in the respective environment.
Only operate the products within the defined temperature range.
The instructions should be passed on to the user by the person carrying out the installation.
Kentix accepts no liability for damage to the devices or components caused by incorrect installation. Kentix accepts no liability for incorrectly programmed units.
Kentix accepts no liability for faults, material damage or other damage.
<\/div><\/div><\/div>
Use of the products, transport and storage<\/span><\/div>
Protect the device from
moisture, dirt and damage during transportation, storage and operation.<\/div><\/div><\/div>
Battery powered products<\/span><\/div>
Do not use the products in potentially explosive atmospheres.
Only operate the products within the defined temperature range.
Installation and battery replacement may only be carried out by trained specialist personnel in accordance with the instructions.
Do not charge, short-circuit, open or heat batteries.
Observe the correct polarity when inserting the batteries.
The devices must always be operated with the batteries intended for the product.
When changing the batteries, always replace all batteries.
Dispose of old or used batteries properly.
Keep batteries out of the reach of children.
<\/div><\/div><\/div>
Maintenance
<\/span><\/div>
Kentix devices must be checked for functionality as part of annual maintenance.<\/div><\/div><\/div>
Disposal<\/span><\/div>
Electrical appliances and batteries must be disposed of separately from household waste.
<\/div><\/div><\/div><\/div>\n\n

Controls<\/h2>\n\n

Front<\/h3>\n\n
\"\"
KeyPad touch front<\/figcaption><\/figure>\n\n

Key layout<\/h3>\n\n
\"\"
KeyPad touch key layout<\/figcaption><\/figure>\n\n
  1. Arming – Leaving the RoomOK: 5-second audible signal (on\/off), arming LED flashes green <\/i>, MultiSensors emit an audible signal according to the set delay time.Not OK: 3-second audible signal (on\/off), arming LED flashes red <\/i><\/li>
  2. Disabling – Entering a roomOK: 1-second continuous audible signal on the keypad and MultiSensors; LED stays on continuously <\/i><\/li>
  3. RFID reading range: Hold the RFID card as centered as possible on the reader. The function is executed immediately after the correct reading. <\/li><\/ol>