{"id":4077,"date":"2023-03-01T16:46:34","date_gmt":"2023-03-01T15:46:34","guid":{"rendered":"https:\/\/docs2.kentix.com\/knowledge-base\/smartpdu-40he-operating-instructions\/"},"modified":"2024-10-18T09:03:06","modified_gmt":"2024-10-18T07:03:06","slug":"smartpdu-40he-operating-instructions","status":"publish","type":"ht_kb","link":"https:\/\/docs.kentix.com\/en\/knowledge-base\/smartpdu-40he-operating-instructions\/","title":{"rendered":"SmartPDU-40U – MANUAL"},"content":{"rendered":"\n
DATA SHEET SmartPDU-40U<\/a><\/pre>\n\n
KentixONE Operating mode<\/h2>\n\n
SiteManager Operation<\/th>Stand-alone operation<\/th><\/tr><\/thead>
<\/i><\/td><\/i><\/td><\/tr><\/tbody><\/table>
Further information on the operating mode<\/a><\/figcaption><\/figure>\n\n
Overview<\/h2>\n\n
The SmartPDU is optimized for power supply of end devices in data and network cabinets with simultaneous power monitoring, consumption data logging and environmental monitoring and is typically mounted in a 19 inch rack. With the integrated PowerManager and MultiSensor, up to 100 SmartPDUs can be easily managed. The integrated PowerManager is network-compatible and is supplied with power via Power over Ethernet (PoE).The SmartPDU can be operated as the main device (operating mode: Main Device) or in a network (operating mode: Satellite Device) with other SmartPDUs. The KentixONE software is already integrated via the integrated web server (HTTPS). Configuration is performed via web browser and, depending on the operating mode, locally on the SmartPDU itself (operating mode: Main Device) or on a central instance such as SiteManager or PowerManager (operating mode: Satellite Device).The SmartPDU has a height of approx. 178cm (40 height units) and thus fits into all common server cabinets from 42 height units. The SmartPDU delivers a maximum output power of up to 22kVA (depending on the version) and is therefore ideally suited for server racks with high power consumption. Depending on the version, the SmartPDU-40U is also available as a two-phase variant so that electronic terminal devices are protected against possible failures by two separate power supplies. The power is supplied via a 3 meter long connection cable and a CEE plug (IEC60309) corresponding to the design.<\/p>\n\n
Safety instructions<\/h2>\n\n
Installation<\/span><\/div>
Installation and commissioning may only be carried out by trained specialist personnel in accordance with the instructions.
No modifications of any kind, other than those described in an appropriate manual, are permitted to Kentix GmbH products.
Certain levels of protection must be provided when installing Kentix equipment.
Observe the relevant regulations for installations in the respective environment.
Only operate the products within the defined temperature range.
The instructions should be passed on to the user by the person carrying out the installation.
Kentix accepts no liability for damage to the equipment or components resulting from incorrect installation. No liability is accepted for incorrectly programmed units.
Kentix shall not be liable in the event of malfunctions, damage to property or other damage.
<\/div><\/div><\/div>
Use of the products, transport and storage<\/span><\/div>
Protect the device during transport, storage and operation from
Protect moisture, dirt and damage.<\/div><\/div><\/div>
Battery powered products<\/span><\/div>
Do not use products in potentially explosive atmospheres.
Only operate the products within the defined temperature range.
Installation and battery replacement may only be carried out by trained personnel in accordance with the instructions.
Do not charge, short circuit, open or heat batteries.
When inserting the batteries, pay attention to the correct polarity.
The devices must always be operated with the batteries intended for the product.
When changing batteries, always replace all batteries.
Dispose of old or used batteries properly.
Keep batteries out of the reach of children.  
<\/div><\/div><\/div>
Maintenance
<\/span><\/div>
Kentix devices must be checked for functionality as part of annual maintenance.<\/div><\/div><\/div>
Disposal<\/span><\/div>
Electrical appliances and batteries must be disposed of separately from household waste.
<\/div><\/div><\/div><\/div>\n\n
\n
Controls<\/h2>\n\n\n\n
Front<\/h3>\n\n\n\n
\"\"
SmartPDU-40U Front view<\/figcaption><\/figure>\n\n\n\n
  1. Network connection (PoE) and Kentix system socket, Integrated sensors<\/li>
  2. Connection area 3 (L3) with fuse C10\/C16<\/li>
  3. Connection area 2 (L2) with fuse C10\/C16<\/li>
  4. Connection area 1 (L1) with fuse C10\/C16<\/li>
  5. Current meter with display (MID calibrated) and residual current measurement (RCM) measurement<\/li>
  6. Power connection depending on type 5-pole 16\/32A or 3-pole 32A, cable length 3m<\/li><\/ol>